Search results for query: *

Need the dome light assembly (bracket/bulb, socket & wiring harness. for a 2 door or 4 door sedan. It the rectangle one.

I'm gathering parts for installing my headliner. What style shape is the dome light?, Round, Rectangle? Did Sedans have a dome light. Anyone have a photo.

Gathering up parts for installing my headliner. 1) What position do they get installed at? My hardtop was the shortest in front and longest in rear. Is a Sedan the same? 2) My hardtop had a spring on the back bow. Don't remember is there was one or two. Is the sedan the same? 3) My...

I need the headliner sail panels for my 1965 dodge Coronet 2 door sedan. I can't find anyone who sells them. Hardtop ones are readily available. If someone could send me a pattern. I could make them. Don

Need one good spindle for 65 B-Body -Dodge Coronet- for 10" drum brakes. Spindle shaft must be in good condition with no rust or wear and not from a wrecked car. Rust on the upright is ok. I believe left fronts are the same. Also some later years are the same.

Found all the exhaust pushrod rubbing severely on the head gasket. Got deep wear spots in less than 100 miles driving. I can replace the pushrod, install new head gaskets but will end up the same. How do I clearance the holes in the head gasket without wrecking them? Is this normal?

Got home a couple weeks ago after driving to the Amblewagon plant in Detroit to pick up my new 1965 Dodge Altered Wheelbase race car. As I got the last one they gave me the jigs for the front end modification. I noticed in the box they also had a jig for positioning the torsion bar anchors...

What the PN for the correct water temp sensor. I've been told TS-17, but looking on the web it seems its for TS-17 is for later years.

Anyone know where I can get my 65 Coronet rear bumper straightened and rechrome in Arizona or southern California? The last ones I had restored was from a vendor at the Mopar Nations in 2014. It was called Coast to Coast and they were located somewhere in the West Los Angeles area. I could not...

I install SS springs on my 65 Sedan and the drivers side sits higher by one inch. I always thought the passenger side would be higher. I have the # 456 ( has more leafs) on the passenger side and 457 on the drivers side. The car weights 3310 without driver. Also does the pinion angle change...

Will a later year (like 66-67-68) wiper arm fit a 1965 splined pivot shaft? Is the width at the bayonet end the same? I need a drivers side arm for my 65 Coronet. I understand the later year arms are longer. So, I was thinking to cut the end off of one and rebending it to match the length and...

Just got my rear original looking wheels. Got them from Wheel-Smith. Only took 5 days after ordering and they were on my doorstep. Great service. Got 7" backspacing to fit with my mini tubs and inboard springs.

What is the o-ringed big plug for at the front of the block just above the oil pump?

Need a set of 8 bolts to attach the flexplate to the crankshaft. This is for a Gen II Hemi crate motor. 8 each 1/2" diameter, 20 Tpi, 1/2" long. Aftermarket or OEM. ARP bolts are on backorder for the foreseeable future.

I have a reproduction headliner for my 1965 Coronet 2 door hardtop. I already glued in the insulation and sail panel boards. I have all the bows and clips. I need someone in the phoenix area to help me install it.

Getting ready to cut the end off my 1965 Coronet steering shaft so I can lengthen it when I noticed a hole in the shaft. Its just over an 1/8" diameter and about as deep. My 66 is thy same. Whats it for?

I just rebuilt my manual gearbox. I installed a 20:1 gear Mopar PN: P4007612. Now I go to install it and the coupler does not fit. My old gear and coupler have a dead spline, but the new 20:1 gear does not. What goes on here?

Who sells individual pieces? I don't need a complete set. I just want the 4 inner door panel ones, plus one extra for the inner front door. .

One of my clips got broken taking off the molding-trim that goes above the door on a 2 door hardtop Coronet or Satellite. This is sometimes called drip molding or roof rail molding. I tried the reproduction ones and they are junk. I need at least one original.

Lost some more parts. I need the clips that hold the brake line along the lower firewall to floor flange. There is one clip in the center at the top of the tunnel. It looks like a hair clip fits into a hole on the floor flange. Then there are two semi flat clips, one on each side of the tunnel.