Search results for query: *

I'm selling a set of re-chromed front and rear bumper guard stands WITHOUT rubber that I didn't use on the Road Runner project I completed a few years ago. These are show quality pieces at a great price! Three of the four stands have new mounting studs welded on and all have new flanged nuts...

I'm looking for a presentable reasonably priced RR trunklid emblem. It doesn't need to be perfect - just affordable, unlike the reproduction emblem. Thanks.

I need the three strips that go between the rear bumper top and sides and the car body. Thanks.

Did 73 B-bodies have rubber bumpers on both the fuel filler door AND the lower rear valance under the fuel filler door? I ordered what was caller "license plate bumpers" and these clearly fit the 1/4" holes in the middle of the plate door (not the holes in the corners for the plastic push in...

I'm looking for a good two-speed wiper motor that will fit a 1973 Road Runner: one that moves the wipers back and forth (when turned on) as well as parking the wipers against the stops on the bottom of the windshield trim when they are turned off.

On the '71-74 B-bodies are the windshield wipers supposed to stay above or ride on top of the large stainless trim at the bottom of the windshield at the bottom of their stroke? If you clock them so they stay above the trim piece they angle up pretty far onto the windshield when they are off...

What years, if any, were reflective stripes used on Road Runners?

Has anyone run across some generic rubber floor mats that are readily available at a reasonable price that fit the floors of '73-74 B-bodies? Classic Industries has a few sets to choose from but they are all over $120/set and say something like "Road Runner" or "Plymouth" on them which I'm sure...

These are holes I found on the ledge that the front of the seat cushion sits on on my '73 RR project: . I can't find anything in my collection of parts from the car that looks like it could go there, both over and under the floor. I need to figure out what to do with these holes because I...

I'm having trouble figuring out what parts I'm missing for the wiper linkage on my '73 RR project. How do the linkage rods connect to the pivots and what hardware is needed to put it together? Is anyone selling these parts new or do you have to get them off of a salvage car? I have the pivot...

Did all factory B-body AM/FM stereos from this era use external stereo faders, or did some have the fader built into the radio itself? I'm guessing if you hook one of the stereos that need a fader up without a fader it will still make sound, right?

I carefully pried the drip rail moldings off of my '73 RR project a long time ago to paint it so I could make sure to get paint underneath where they overlap the sail panels, and in so doing they developed an upward bow to them that makes them impossible for me to snap back on. I sent them to a...

What sort of screws and so forth were used to attach the side mirror mounting plates to the outer door panels on the 1973 Road Runners? Thanks.

I made a post the other week about the stereo wiring layout for the 71-74 B-bodies and someone posted this shop manual page: . On the "stereo wiring" diagram are the "X54A-20BK" wire and the wire coming out of the molex connector connected to the "X53-20BK" wire loop going to both be body...

How was the original 5X7" rear deck speaker mounted in '71-74 b-bodies? The holes for it look pretty small so I can't tell if they were screwed in from below with #8 sheet metal screws or attached with tiny (about #6) machine screws and nuts, or some other way that is less obvious. I want to...

So stereo on 1973 b-bodies was apparently one front dash speaker and one speaker on the rear package shelf. There are two factory oval cut outs on my car's package shelf, but the right one is the only one that is recessed and has holes punched for a 6X9 speaker, so would that have been the...

On which side is the horn located on '73 Road Runners? It looks like there are holes for it to be mounted on both sides of the fronts of the inner fenders, and there are electrical leads for it on both sides as well. I suspect that is because the Satellites got dual standard honk horns. Sorry...

I need a fairly straight one of the aluminum moldings that fits on the bottom of the grill for one of these cars. Thanks.

Can someone please tell me what type of screws were used to attach the headlight bezels on these cars to the plastic push-in nuts on the front of the fender they go into? The holes in the bezel are fairly large so I'm thinking either oval head screws with countersunk washers were used, or...

I need seven of the 5/16"-18 nuts with the built in LARGE (over 1" dia) free spinning washers that were used on the back part of Mopar car fenders to fasten them to studs on the inner structure. I don't know what years they used these, just that they were used on a number of different car models...