Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Replaced the ignition switch in my '69 plymouth (non column mounted) and it's really difficult to get the bezel to tighten and therefor the switch is a little sloppy. Is there a tool for this that grabs several of the slots at one time to turn it tightly? I've been using a small flathead to try...
Hi all,
Recently been parking my '69 plymouth in the attached garage and there is a very strong gas smell. IF I open the garage the smell permeates in about 10 minutes but it's very strong. Is there something I can do to lessen the odor and or eliminate it? My gas cap is vented and so it the...
My one experience with PST has been horrible.
I am upgrading the drum brakes to disc in my 1969 roadrunner (Gen 3 Hemi w/whipple). When I removed the upper control arm on the passenger side, one of the upper cam bolts broke. I went online and found that PST sells them for $15 each. I ordered...
Hello all,
I have installed a Gen 3 6.4 in my '69RR with stock K member and a flaming river manual box. I installed the 2" TTI header on the driver side and then realized the tubes would not allow the starter to slide through or around them so I had to uninstall them and install the starter...
Ok guys I have not been able to install the Gear Vendor housing onto the 727 smallblock. Well technically I did once but then i realized that the transmission arm was not properly seated in the housing because it wouldn't shift so I unbolted the housing and attempted again. Unfortunately, I got...
Hello again,
I will attempt to install the gear vendors unit soon onto the 727. It has a reverse manual valve body and the GV instructions say to make sure the transmission is in 1st or L gear. I looked online and can't find an illustration of where the transmission arm would be on a 727...
Hello all,
I am installing a 10" torque converter into a 727 small block. I believe I have fully seated the converter because it sits inside the bellhousing 1.25" (measured this). My first question is, if I pull on the converter it will slide out all the way, is this suppose to happen? For...
Hey guys,
My engine arrived and I've run the engine management wires through the firewall but don't know where I should mount the plug in management board. Does anyone have pics of where they mounted theirs inside the cab?
Also, I removed the gas pedal and am not quite certain where to mount...
I just received my Cope transmission SB 727 and since the engine and transmission are out of the car I thought it might be easier to install the Gear Vendors to the transmission now rather than when I'm under the car and have much less visibility and space? I've watched some videos online but...
Hi guys,
I picked up my John Cope Transmission today from the freight terminal and will unwrap it tomorrow. Thanks for your feedback on making this happen! For anyone that has a transmission or even engine shipped to them you can have it shipped to the local freight company and pick it up...
Hi Guys,
Another question for you :)
The transmission I have ordered from John Cope is ready to ship, yah! However, John tells me I need a commercial address in order for him to ship it to me.
I live in a residential house in a suburb just South of Sacramento, (save the...
Hi guys,
As you may know I am converting my '69 RR that was raced into a street car with a Gen3 Hemi . I've asked a few questions so far to help with the conversion and I've had great answers which allowed me to make progress.
My question now is;
The battery was relocated to the rear trunk...
I removed the carpet/pad and seats to cut off some small welds inside my '69 rr and noticed some daylight coming through the floor pan behind the driver seat. I de-greased and cleaned up the rest of the floor pans inside with a wire brush and it appears ok. There was some light surface rust in a...
The previous owner welded front and driver seat bump/stop plates to the roll bar behind both front seats. The car was raced and I believe the seat bumps/stop plates allowed the driver to sit more forward while also touching the plate for stability.
I would like to remove them carefully so the...
Hi guys,
I sold the old plastic race seats that were in the car and purchased new Corbeaus. Problem is I no longer have the front seat bolts that attach the seat track to the floor plan; 4 per seat. The new seat tracks say they work with the original bolts. I don't need to have original bolts...
Anyone here have a $50 of Summit Bucks code/coupon that they don't plan on using? I think i misplaced mine and have looked high and low for it...
Got an order I'd like to make and save a bit.
Thanks in advance.
Hi Guys,
I will be shipping a 6.4 392 engine out of a 2013 Challenger soon. I was able to find plugs/caps for the coolant opening and oil openings from the oil cooler on the engine but I can't seem to find a cap/plug for where the oil filter would go. The freight company wants the oil filter to...
Hi guys,
I just installed the flaming river manual steering box and pitman arm. My question is the pitman arm does not seem to seat as high on the steering box sector as the original steering box.
I believe that the shaft is tapered so the pitman arm will only go on so far... From what I can...
Hi guys,
I may be getting my roll cage re-done due to the fact the previous owner had the rear two bars go through the upper portion of the rear seat. Because of this the upper rear seat can't be installed.
I'm looking to have the bars come up and over the top rear seat and into the trunk...