Search results for query: *

Hey all, I have fully rebuilt my 1966 Charger. I rebuilt the wiring harnesses as well, nose to tail. Everything is up and functioning except the Temperature and Oil Pressure gauges. Both sensors are NEW. I think I should be getting about 5v at the sensors since the wiring diag. shows 5v. What...

Hey all, I am not sure this is the right location for the temp sensor. Can someone verify this?

Hey all, I installed a 440 in my 66 dodge charger. First time I have worked with a 440 block. It has HP exhaust manifolds. Runs great but I am noting steam from second to rear right exhaust bolt. Did I miss something when assembling the exhaust?

Hey all, I rebuilt my 727 trans (66 Charger) when I moved it from the 318 housing to a big block housing. When I put it in gear, it clunks into drive or reverse. Fluid level is good. Wondering if it is a setting. Maybe I need to tighten the bands?!? FYI... I have never rebuilt a trans before...

Hey all, I have a 67 440 with a Edelbrock 750. The pump seems like it is not putting out enough fuel. The engine idles fine. But rev it up and it starts to die. The pump is new but maybe not the right one for this application. The inline filter does not even fill up half full. Suggestions on a...

Hey all, I am looking for the rear glass stainless trim. Just need the lower section. Thanks in advance to all who reply...

Hey all, I have a 1966 Charger that I have been working on for 7 years now. I am ABD... All but done with this car. As some of you know, I have had this car since I was 16... I turn 62 in a few weeks. The interior is done, the engine is done, the exterior is done... except the rear stainless...

Hey all, I have read many posts here and can see I am not the only one struggling with this issue. As a primer, I've had this Charger since i was 16 a towed it around everywhere I went since. I rebuilt this 66 from the ground up over the past 7 years. The steering has new upper and lower...

Hey all, After a trans rebuild (full disclosure, first time I ever rebuilt a trans), I finally have my 66 Charger 440 running. I filled it, started the engine then, with the axle on jack stands, I cycled through the gears. Tires spin forward and reverse. Went through a few times. I put the...

Hey all, A few years ago I rebuilt my 727-A transmission. First time I have ever rebuilt a trans. I happened to find an old training video that took me from start to finish, tear down to assembly. Roll forward a few years (after body work, paint and engine rebuild) and I have the car ready to...

Hey all, My 1966 Charger front fender chrome has some challenges. The LH side was damaged. The RH side was gone. I just finished painting it and could not go back, cut, weld and close all the chrome. So I made a model of what I think are original shapes. And cast new ones in Aluminum...

I have an odd problem I need to bounce off the brain trust. I am just about finished with my full rebuild of my 66' Charger. I rebuilt the dash, body and engine wiring harness... replaced every wire with new color and trace matching wire. No fuses installed yet. All switches in the off position...

Hey all, I am getting to the end of a 7 yr rebuild of my 66' Charger. I've had this since I was 16 and been working on it for ages. I have a few things that still need to be addressed but I am on the final lap. I am looking for a list of where decals and placards go? Jacking info, tire...

Hey all, Does anyone know the thickness of the 440 Source dampener shown here? Internal / External Balance Black Damper-440 Source I need a later model dampener for my 440 block that is 1-5/8" thick. The one I have is a 65 year and is 7/8" which is throwing off the pulley alignment by 1/2".

Hey all, What is wrong with this picture? Do I have the wrong pump or what? The Power steering pump pully is off by 3/8" to the rear. The alt is off by a mile. If I put the deep neck pump pulley on, it rubs on the crank pulley. Really lost on this. The crank and water pump pulleys are new. I...

Hey all, I recently purchased a set of exhaust pipes from a vendor. I got them Friday and dry fitted them yesterday. The right-hand side fit perfectly. The left-hand side is off by a about 30 to 45 degrees. I asked the vendor and he said I had the wrong casting numbers for the 67 exhaust...

I have the distributor from my old 318 block. Will it fit a 1967 440 block?

Hey all, I am finishing up my 1966 Charger. I swapped out the original 318 for a 440. I have standard exhaust installed and I the column knuckle to the steering gearbox is just touching... clips the exhaust as the wheel turns. Is there a problem with the steering joint or do I need to change...

I had a 318 with a 727 and installed a 440 then upgraded the transmission housing by rebuilding the old gears and putting them into the new housing. I am struggling with fitting the drive shaft. It does almost all the way in but not far enough and it seems to hard-stop. I am not a transmission...

Hey all, I replaced my 318 with a 440 and bought a replacement pos. batt harness from Classic Industries for the 440. Anyone have a picture of how the cable routes past the exhaust? I know it's close but I want to make sure I am routing it the correct (factory) way. Thanks in advance...