• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

Search results for query: *

  1. BPBP440

    8 3/4 Housing - Is this crazy?

    Just tore down and cleaned up my 70 B-body 8 3/4 rear. The housing has this terrible welding on it, yet the inside is as it should be. Looks like the flange washed out and it was built up with terrible weld. Factory???
  2. BPBP440

    Another Spark Plug Wire Thread

    70 440 electronic ignition, long tube headers. I bought MSD Street Fire wires many moons ago and am just now installing. They have straight boots on the plug side, and 6-90 degree 2-straight boots in the distributor side. Straight boots are only long enough to reach 2 or 4, maybe 1. Also, the...
  3. BPBP440

    Coil Bracket for Edelbrock Performer

    Is there a special coil bracket for the offset (height) coil bracket mounting bosses on the edelbrock Performer? Or, do I just need to make a nice spacer? Thanks
  4. BPBP440

    727 Dipstick Tube O-ring

    Does anyone have the specs for a dipstick tube o-ring. Doesn't seem to be available as that part from the autoparts and I don't have time to order one online. If it is a standard o-ring size and material I may be able to get from grainger next day. Thanks.
  5. BPBP440

    Header studs - No Shoulder- Okay?

    I ordered Mr. Gasket header studs for my 440 906 heads and to my surprise they have no shoulder with a continuous thread from end to end. I know the shoulder is not a sealing surface, but I imagine the shoulder interrupting the spiral leak path would help with reducing the leak path. Any...
  6. BPBP440

    727 Neutral Safety Switch Seal

    Is this seal just a metal “conical” washer, or is there supposed to be rubber molded on it?
  7. BPBP440

    Wheel Stud Removal - 8 3/4 Rear

    Looking to replace the wheel studs from L to R hand thread since the disk brake conversion is R hand thread. Is the room to change the Rear Studs without pulling the axle?
  8. BPBP440

    Valvoline max life synthetic

    Valvoline max life (high mileage) Dexron VI synthetic is really cheap at Walmart. Like 18 bucks a gallon. Planning to use Synthetic Dexron VI in my fresh 727 rebuild. What is the big difference between the max life and the regular Valvoline Dexron VI synthetic. Max Life advertises special...
  9. BPBP440

    ARP Bolt Torque Questions

    I am using ARP Flex Plate Bolts, Torque Converter Bolts and Bell Housing Bolts for my 440/727. The only torque value I found from ARP was for the Flexplate Bolts (7/16") - 75 ft-lbs using their assy lube. For the other bolts they simply refer you to a spec sheet, which requires you to know the...
  10. BPBP440

    Recommendations On Header Bolts?

    I am surprised at the huge range in prices for header bolt sets. I am putting Doug Thorley headers on my 440 (906 heads) in a 70 B-Body. What bolts do you all prefer and why? Thanks-
  11. BPBP440

    1970 440 Piston Compression Height?

    I am looking at putting some NOS pistons in my 440. They are NOS pistons, PN 3420214, correct for '70 (w) 4bbl......listed as 9.75:1 CR. I was told they are flat tops and the compression height is 2.000. However, when I run the CR calculations, I get closer to 9:1 with open chamber heads. I...
  12. BPBP440

    RV 727 Torque Conv Stall Speed?

    Does any one know if a 78 440/727 in an RV had a higher designed stall than a pass car application? Posting my RV trans to Craigslist and trying to decide if I should hold onto the convertor.
  13. BPBP440

    Initial Tuning Advice - 440

    I am about ready to start my new motor up. Pump Gas motor, not looking to squeeze every last HP out of it. It is an iron head, 440 with ~9.3:1, 270/.470 Hydraulic cam, an 800 CFM Edelbrock carb and headers. MSD Blaster coil and a Procomp electronic ignition set-up. What plugs and what...
  14. BPBP440

    Any recommendations on a 727 Overhaul Kit??

    Looking to rebuild my first 727. Bought a video, read a book, have the service manual, read the great blogs here.... ready to do this. Lots of you guys have heavily modified and impressive transmissions. My car however is a cruiser, mild 440 build, hemi converter, likely a 3:23 suregrip...
  15. BPBP440

    Daaco "hemi" Reman Converter for my 440 - good or bad idea?

    I have received a couple of opinions to use a Hemi converter as a budget minded option and get a bit more stall over a stock 440 unit. Looks like this could run about $100 for a Daaco reman unit, plus another $50 or so for an aftermarket flexplate to accomodate the 10" bolt circle. Is...
  16. BPBP440

    Max Wedge Picture

    Came across this max Wedge picture. Not sure who the individual is, but I enjoyed the old internal Chrysler picture and thought you guys might too.
  17. BPBP440

    Ring Gap for New Speed Pro L2255F40???

    Ring Gap for New Speed Pro L2355F40??? Bought an engine rebuild kit from Summit, which included a standard fit ring set for .040 over 440 (4.360). The ring set is ZE424K40, cast iron moly coated top ring, cast iron non coated 2nd ring. I am surprised at the ring end gap, which is .035-.036...
  18. BPBP440

    Performer RPM with Six Pack Style Aircleaner - Clearance Okay???

    My car came with a 6 bbl style air cleaner (but not on car), with base to fit my single 4 bbl. I have seen some cautioning about checking hood clearance with a Performer RPM intake manifold. Does anyone know if a 440, with RPM Manifold, 800 CFM Edelbrock AVS and 6 bbl style air cleaner will...
  19. BPBP440

    Anyone have a 440 Engine Fastener Size List?

    I am rebuilding a 1971 440 that is riddled with aftermarket chrome fasteners and very few washers. I am not seeking an originally correct fastener rebuild, but would like to replace these chrome fasteners with bolts of the correct length and washers where originally used. Main concern areas...
  20. BPBP440

    Help with converter selection

    So, now that you guys helped me decide to stick with my current cam, I need to choose a converter. Again, this car will be driven on the expressway a fair bit, plus cruising with family. Engine specs below. Currently a 2.94 gear, hoping to upgrade to a 3.23 suregrip soon. The coverter now...
Back
Top