• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

1966 Plymouth Satellite HP2

My '67 R/T has the metal shields, but it was a Dec. '66 build.
 
should probably be putting some of those torque boxes in Bella! is that something available after market that are well made? my sons a pretty good fabricator could likely make some up easier with measurements! he made the bellhousing from scratch mating the rb to a ZF so a torque box would be a breeze!
 
should probably be putting some of those torque boxes in Bella! is that something available after market that are well made? my sons a pretty good fabricator could likely make some up easier with measurements! he made the bellhousing from scratch mating the rb to a ZF so a torque box would be a breeze!
US Tool sells them, or at least a rendition. '66 only has the rears and the plate up on the rear spring hanger channel. Newer cars also had them on the front rails... Torque Box Set
 
Well now you tell me! I guess National Moparts is the only one that lists correctly as 67 up... as everyone else lists 66 up and I figured NM was wrong. Now is that $105 wasted or do I need to find another car in need.....
Maybe you would like to get our 67 L code Charger and then put your shields on it???? Then you wouldn’t have go through the hassle of advertising yours. Just trying to be helpful.
 
K frame splash shields off the car and on the parts shelf, waiting for the next car to be installed on!
1966plysathp2ptm 129.jpg

Passenger door has never been opened up either. Wanted to fix the door card, so popped it off and sprayed Krown in this one as well.
1966plysathp2ptm 106.jpg

Passenger card part #2656452 F
1966plysathp2ptm 103.jpg

Inspectors signature.
1966plysathp2ptm 104.jpg

Top edge stainless was loose on this door as well, but at least hadn't started wearing the paint off.
1966plysathp2ptm 105.jpg

Vapor barrier glued and paper taped back into place.
1966plysathp2ptm 109.jpg

Vinyl wrap loose on both door cards on the top rear corner. Did my best to glue and staple them to snug up the wrinkle.
1966plysathp2ptm 112.jpg

Trying to get the trim to stay in place with a few dimples. Pretty obvious why they switched to trim that screws to the door in '68, that the card tucks up under and holds tight.
1966plysathp2ptm 117.jpg

Added some tarp tape for good measure.
1966plysathp2ptm 119.jpg

Window crank handles part # 2299927
1966plysathp2ptm 122.jpg
 
Like I always say, if it's off....
1966plysathp2ptm 137.jpg

57 year old cranks in better shape than brand new reproductions that the knobs fall off after 5 cranks.
1966plysathp2ptm 142.jpg

Passenger door all back together. Need to give that paint a buff.
1966plysathp2ptm 127.jpg

Same deal on the drivers side.
1966plysathp2ptm 131.jpg
 
Metal splash shields that I have on their way from Michigan from Big Bill. Will need a blast and paint, but I may even make patterns from them and bend up some new ones. Pending how that goes their may be a more than a few made.
1966plysathp2ptn 001.jpg

Gonna see if I can bring the upper door panels back to life.
1966plysathp2ptn 004.jpg

1/2 there...
1966plysathp2ptn 008.jpg

Good as she's gonna get, right after I wipe that spot I missed..
1966plysathp2ptn 010.jpg

Amazing how hard it is to get a camera to focus on date etchings on glass. Going around the car to see just how correct it its. Rear glass mfg 115. November, 1965.
1966plysathp2ptn 013.jpg

Rear drivers glass 10th month of 1965. Drivers door glass the same 105M but couldn't get a focus on it.
1966plysathp2ptn 016.jpg

Not sure on the windshield, possibly it's a replacement at some point in time, not sure on how to read the code on this one. 15 could be January 1965, not sure.
1966plysathp2ptn 018.jpg

Passenger door glass and rear quarter glass both December 1965. Car was built December 15th.
1966plysathp2ptn 019.jpg

Passenger vent glass also December 1965.
1966plysathp2ptn 020.jpg

Drivers vent glass November 1965.
1966plysathp2ptn 023.jpg
 
Last edited:
Mirror flops around everytime you open and close the door. Hoping I can tighten up the pivot by taking it apart.
1966plysathp2ptn 034.jpg

Original pedestal casting part #2299321
1966plysathp2ptn 037.jpg

Mirror is held in by a metal ring. Push in on the mirror and hook and lift the ring out.
1966plysathp2ptn 040.jpg

Spring in behind the mirror.
1966plysathp2ptn 045.jpg

Even the mirror glass is date correct for the car. August 1965 ( 8- DMT-5). Took me 15 minutes to get this shot.
1966plysathp2ptn 050.jpg

I tried a few tricks trying to tighten up the metal friction strap with no luck. A blob of Gorilla glue and we'll see if it bites to the pivot come tomorrow. No way I'm trying to drill those rivets out holding the friction plate. When this fails to work I'll put it back on, adjust, get out the passenger side and glue the sucker again.
1966plysathp2ptn 055.jpg

Damage that the mirror has done to the trim by flopping around.
1966plysathp2ptn 057.jpg

Enough for a Sunday. A few tunes and it's closing time..
1966plysathp2ptn 064.jpg
 
I’ve heard of using a couple drops of low strength loctite on those mirror pivots to tighten them up but I’ve never tried it. There’s a purple variety that is supposed to provide a greater friction fit to threaded fittings.
 
There was a mirror hack from Rick Ehrenberg in Mopar Action several years back that involves super glue on the ball. I’ll look for it when I’m home tomorrow night. I posted it once before.
 
There was a mirror hack from Rick Ehrenberg in Mopar Action several years back that involves super glue on the ball. I’ll look for it when I’m home tomorrow night. I posted it once before.
Basically what I did and it worked. I put it back on today, adjusted it with a view down the stainless trim and slammed the door 5 times and it didn't move. If it does I'll add some glue to the outside of the ball and roll it around, then into position and let it set.
 
There was a mirror hack from Rick Ehrenberg in Mopar Action several years back that involves super glue on the ball. I’ll look for it when I’m home tomorrow night. I posted it once before.

I think clear nail polish was used.
 
Our buddy RC with a survivor '66 Belvedere II keeping me on my toes with "correctness".
1966plysathp2ptn 073.jpg

Engine to body ground wire that is missing on mine. Not even sure where it's getting it's body ground from.
1966plysathp2ptn 074.jpg

Unique wire holder bracket that many guys with hemi cars have never seen. Appears it's to keep the wiring harness off the manifold heat pipes.
1966plysathp2ptn 075.jpg

I also noticed that my voltage regulator is mounted 180* out from factory and I need to find a ballast resistor bracket that has the extra hole for the "lock" bump. Think I have one in the glove box of the Superbird.
1966plysathp2ptn 099.jpg

Now to make a ground strap, you'd think I'd have something in this little collection of mine.
1966plysathp2ptn 101.jpg

Story of my life, too short!
1966plysathp2ptn 104.jpg

Found one that I can work with. Just need to reshape the termination to somewhat match factory
1966plysathp2ptn 108.jpg

That'll fake it good enough.
1966plysathp2ptn 112.jpg

Then some wire covering tube to cover the bare wire and need to find a termination for the engine end.
1966plysathp2ptn 114.jpg

Bag of those will do it and a finished ground strap.
1966plysathp2ptn 121.jpg
 
Almost forgot the engine paint..
1966plysathp2ptn 123.jpg

Stole a factory bolt off the '64 Dodge.
1966plysathp2ptn 126.jpg

Voltage regulator turned around to be factory correct. Better shot of the ballast resistor with the incorrect retainer bracket.
1966plysathp2ptn 132.jpg

Back into the old Beach tool box again.
1966plysathp2ptn 135.jpg

That looks about right.
1966plysathp2ptn 137.jpg

4 or 5 dips.
1966plysathp2ptn 142.jpg

Left to dry for the night.
1966plysathp2ptn 150.jpg

Ground strap and wiring hanger installed today.
1966plysathp2pto 014.jpg

Correct lower shifter boot for the Inland shifter arrived Canpar today.
1966plysathp2pto 018.jpg

I don't think this install is going to be any fun at all. The coming days will determine that.
1966plysathp2pto 019.jpg
 
Last edited:
Pretty much factory correct other than carbs and a battery. I have the correct '66 OE carburetors, just don't have the hair left to play with them.
1966plysathp2pto 029.jpg

Air cleaner assembly back on. Will "build" a correct script battery in the days to come.
1966plysathp2pto 031.jpg

Most would never even notice the piece missing out of the fan shroud, right below the upper radiator hose, but I of course did.
1966plysathp2pto 035.jpg

Was hoping I could get the shroud turned a bit so the repair area would be level, but a no go there. No way I'm taking the fan, etc apart to extract it so we'll fix it on the car.
1966plysathp2pto 038.jpg

A few sharp notches for the repair to bite into.
1966plysathp2pto 040.jpg

Cut and bent up a little forming "mould".
1966plysathp2pto 042.jpg

Form put in place with a piece of wax paper between it and the shroud.
1966plysathp2pto 043.jpg

My go to..
1966plysathp2pto 050.jpg

Form clamped in place then the JB Plastic Bonder on to fill the missing piece.
1966plysathp2pto 056.jpg

Not bad. A bit of clean up tomorrow once it's fully hardened.
1966plysathp2pto 067.jpg
 
Last edited:
Auto Transport Service
Back
Top