• When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.

For the Love for my Father, My 69 GTX Restoration

Status
Not open for further replies.
Got back from vacation and now on my second vacation, the GTX!
Getting the headliner parts and related parts installed. If all goes as planned my headliner installer will be here to install everything this Saturday.

Below shows the difference between an original and a new dome light set. Settle variations between the two. The biggest difference is the the harness. It is a thinner gauge and lacks part numbers. The chrome housing is almost identical to the original and clips in the kit are different in size and lack the rubber coating. The lens cover is close but not close enough. So I will use the chrome housing from the new kit and all other original parts will be used.
DSC04642.JPG
DSC04643.JPG
DSC04644.JPG
DSC04645.JPG
DSC04646.JPG
DSC04647.JPG
DSC04648.JPG
DSC04649.JPG
DSC04650.JPG
DSC04651.JPG
 
The kit only comes with 3 clips and no plug. The original has a plug and 3 clips. Those clips attach on the roof rail inner portion in the specific slots and is routed as shown. The wire cover behind the kick panel was installed and here is a portion of the original tape. It is a thin paper tape 2' wide and was taped across the center of the sleeve. I purchased the tape from Frank Badalson and that will be put on towards the end of the build.
DSC04663.JPG
DSC04664.JPG
DSC04665.JPG
DSC04666.JPG
DSC04667.JPG
DSC04668.JPG
DSC04669.JPG
DSC04670.JPG
DSC04671.JPG
DSC04672.JPG
 
Sail panel boards....What a pain. NOS is long gone and good used originals are impossible and I searched for a long time. If I ever do run across some I have all the hardware to replace if nescessary. My old ones were unusable. The new boards are made by REM. Overall, the main problem was the same clip retainer was in the wrong position. They are held on by double sided tape and easy to remove. So I had to reposition them and I resealed all 4 with gorilla glue epoxy. Headliner bows got painted with a zinc paint Eastwoods tank tone and the ends got the original colors replaced. Headliner has been laid out on the car for a week....
DSC04678.JPG
DSC04679.JPG
DSC04680.JPG
DSC04681.JPG
DSC04682.JPG
DSC04701.JPG
DSC04702.JPG
DSC04703.JPG
DSC04704.JPG
DSC04705.JPG
 
Air grabber

Easiest way to remove this is to pull the hood off the car. The comes the scary part....REMOVING THE RIVETS! You have to be very careful doing this so you do not break the tabs or crack the housing. I drilled out the rivets until the started to spin. You do not want them to sing because they can possibly cut into the housing. Once drilled I take two putty knives, one thin and one thicker and I use the two to pry up on the head to eventually break it free. Slow process but had no problems.
DSC02662.JPG
DSC02663.JPG
DSC02664.JPG
DSC02665.JPG
DSC02666.JPG
DSC02667.JPG
DSC02668.JPG
DSC02669.JPG
DSC02670.JPG
DSC02671.JPG
 
While waiting on the headliner this weekend and a few parts on their way. I will be installing the Air Grabber unit. During removal the last step was removal of the scoops, then the center portion and the two side boxes. So first to go in is the scoops/vents. In 69 GTX honeycomb was an orange red and the roadrunners were red. Old emblems were replace with NOS ones and all hardware was restored except for the screws and stud nuts. Totally auto supplied stainless steel screws and RT specialties supplied the stud nuts. The gaskets are the correct grey color and are from DMC.
DSC04706.JPG
DSC04707.JPG
DSC04708.JPG
DSC04709.JPG
DSC04710.JPG
DSC04711.JPG
DSC04712.JPG
DSC04713.JPG
DSC04715.JPG
 
Scoops installed and tomorrow in goes the air grabber unit...
DSC04716.JPG
DSC04717.JPG
DSC04718.JPG
DSC04719.JPG
DSC04720.JPG
DSC04721.JPG
DSC04722.JPG
DSC04723.JPG
DSC04724.JPG
DSC04725.JPG
 
Air grabber restoration

My unit was sent to a gent by the name of Don Hall and part of his business is called Air Grabber Restorations. He is located in Ohio. This is not some TV restoration where they wash it down and just paint it. The two side boxes are completely disassembled by removing the rivets and replacing them with the correct ones. The doors inside of these are known to be rusted out and to check these the side boxes have to be taken apart.. My unit was in great shape and one of the best he has seen in awhile but it still had a hole and a crack that he repaired. If I didn't provide pics of those one would never know.

Don did a phenomenal job!

https://www.facebook.com/AIRGRABBERRESTORATION/?ref=nf
1084987_578216485555086_1668822279_o.jpg
13668938_1139413929435336_6384600786597282630_o.jpg
13668784_1139413926102003_4193907768480616167_o.jpg
13606732_1139414102768652_8968545990648882043_n.jpg
13653318_1139414119435317_4225771949707659343_o.jpg
13640854_1139414112768651_2965742676151997493_o.jpg
13645340_1139414156101980_4773754611771327001_n.jpg
13613372_1139414232768639_1643345113585380909_o.jpg
13641030_1139414249435304_1015366469389594754_o.jpg
13662310_1139414272768635_4308552991875845171_o.jpg
 
This is not some generic TV restoration...where they wash the unit and spray some paint on it and then claim they are they best...lol

Don's restoration are second to none and his work speaks for itself!
13631595_1149076715135724_2525962439639209852_n.jpg
13615172_1149076738469055_5966270981090743926_n.jpg
13782157_1149076758469053_2593914949955968107_n.jpg
13781947_1149076775135718_629675364606476863_n.jpg
13769524_1149076798469049_9134887504331598969_n.jpg
13680978_1149076821802380_4771724931120402880_n.jpg
13669763_1149076855135710_3942770563230586544_n.jpg
13686678_1149076881802374_4801213673732015218_n.jpg
13620788_1149076905135705_6841636711579776329_n.jpg
13669089_1149076918469037_5147869124348394390_n.jpg
 
Today was not a good day.......was unable to install the air grabber unit. The center section on the passenger side you have to trim the seal so that it sits flush and has no binding. The last pic shows I did not trim it enough and I even went by the original picture I had.:BangHead: I tested it on the front but not on the rear portion. So I put the rear rivet in and when I put the front on in I heard an unfortunate noise....WTF. It is on its way back to Don and I am sure he will give me an earful.....but I followed what I knew and what I asked people. It just was not trimmed down enough....

Every restoration has its up and downs no matter how careful or talented one is....I had my decompression time and to stay positive when it comes back that will not happen again...

Just now I got a call from Don and he will turn this out as fast as he can to get me going on my project...When I called this am his employee took a message and said he was on vacation. So apparently, Don checked in and his employee relayed my message and he called back. He thinks the reason why it cracked was just due to the age of the material. Furthermore, he said they normally do not crack there. That SPEAKS miles of what type of business he runs there, Thanks Don!
DSC04731.JPG
DSC04732.JPG
DSC04733.JPG
DSC04734.JPG
DSC04735.JPG
DSC04736.JPG
View attachment 413639
DSC04738.JPG
 
Last edited:
Hardware kit from Frank Badalson is a nice kit. The bolts are a little longer but has the correct head marking of "F". The clips are correct in the kit with the exception of the outer side box J nuts which I will add to this post later...
DSC04726.JPG
DSC04727.JPG
DSC04728.JPG
DSC04729.JPG
DSC04730.JPG
 
Status
Not open for further replies.
Auto Transport Service
Back
Top