Correct installation of green axle bearings.
- Thread starter chargervert
- Start date
70chall440
Well-Known Member
- Local time
- 1:57 AM
- Joined
- Feb 11, 2018
- Messages
- 4,579
- Reaction score
- 6,344
- Location
- Yelm, Washington
Call Cass (Dr. Diff), he will school you on this subject. Well worth the effort.
- Local time
- 3:57 AM
- Joined
- Jul 1, 2015
- Messages
- 4,615
- Reaction score
- 5,583
IMO....Use the TIMKEN tapered roller bearings installed with the factory OEM style adjusters....and go down the road for miles and miles in complete confidence..... others will disagree and have their own preferences.
BOB RENTON
Cornpatch MO
Well-Known Member
If you are putting together a complete rear axle from various parts, I would use the greens. Tolerances aren't so important. If you are working on one that has all the original components ( such as the center thrust block and the axle end play adjuster ) I would probably go with the stock timptkin bearings. Just be SURE your axles are within clearance on both sides. ...................................MO
Cornpatch MO
Well-Known Member
BTW has anyone here drilled and tapped the axle housing for grease zerks , to grease the rear axle bearings? I know years ago, the factory did that, but I think there was problems with people putting to much grease in them . .........................MO
- Local time
- 4:57 AM
- Joined
- Mar 10, 2010
- Messages
- 29,611
- Reaction score
- 51,173
- Location
- Hanover, Pennslyvania
I've never seen a grease fitting on any factory rear at the wheel bearings. Tell me more.
Cornpatch MO
Well-Known Member
I had a 1956 Chrysler and was in a 1955-1962 finned Mopar forum. IIRC there were a few cars from that era that came from the factory with those grease zerks. Seems to me that it didn't work out so well because people would eventually get to much grease in the bearings and it would squeeze out into the brake drums-shoes..........................MO
- Local time
- 4:57 AM
- Joined
- Mar 10, 2010
- Messages
- 29,611
- Reaction score
- 51,173
- Location
- Hanover, Pennslyvania
I've seen and greased ones on farm tractors (outer axle bearings).
mopar 3 B
Well-Known Member
Not sure what the purpose would be. The tapered rollers are esentually a sealed bearing. Unless a grease seal fails what would be the purpose of adding more grease.
mopar 3 B
Well-Known Member
I have seen them there also. But not many farm tractors have brakes at the axle.
Dipstick
Well-Known Member
Yes, that was the problem, lube room guys would hit every visible zerk at each oil change and that's too much grease for those bearings. Eventually, the excess grease would blow out the seals.
69GTXhrdnox
Member
So in the picture, the retainer ring on the the green bearing (opposite side if O ring of course) will sit against the brake back plate, correct?? Plate goes on axle housing first, then the axle with plate, green bearing, retainer ring will slide in.
In this scenario the retainer/snap ring will sit against the outside of the brake plate. I'm currently installing green bearings on my 8 3/4 rear. It just dosen't seem right. It appears that a portion the outer race (comparatively speaking) is sitting "outside" the axle.
Please Help!!
I've included pictures, with the bearings NOT pressed on yet because i wanted to make sure of how this would fit together. Just dosen't feel right!
- Local time
- 3:57 AM
- Joined
- Jul 1, 2015
- Messages
- 4,615
- Reaction score
- 5,583
Faciously speaking.....its not too late to re-install the origional Timken Tapered axle bearings with the factory end play adjusters. All of your fitmet issues will go away, just follow the FSM procedures for installation and adjustment and you'll go down the road for miles and miles with out any reservations. Just return the Green bearings to the place of purchase for credit. Others will likely have a different opinion. Just my opinion of course.
BOB RENTON
The ring plate you're holding in bottom pic goes btw the pressed axle end bearing and the end of axle. The outer protruding snap ring is to sit flush to this plate when you slide the axles in, if not, the thrust pin may need to be taken out; wasn't necessary with mine but some have said this needs doing if the axles don't fully seat. Back plate goes over this to torque nuts secure axle. That ring plate needs a gasket
69GTXhrdnox
Member
Right, I was just holding everything up there for sequence visual. I was trying to visualize the setup before having the bearing and the collar pressed on. It just didn't seem right to pinch that snap ring on the bearing between the brake back plate and the 5 hole retaining plate. I have since had email contact with Dr. Diff. They said the heavy felt pad they provide is to go between the brake back plate and the 5 hole retaining plate. Otherwise the 5 hole retainer ring would bend over the snap ring.
Last edited:
69GTXhrdnox
Member
It also appears when that (snap?) ring bottoms out against the brake plate a portion of the bearing race will be protruding beyond the axle body. That also bothered me but I guess the area protruding out has no load on it. The bearings are set more inside the axle tube. Just thinking out loud.
Suregrip391
Well-Known Member
Don’t forget, You must use the special gasket between the brake backing plate and 5-hole wheel bearing retainer Otherwise the retainer will bend over the snap-ring.
Similar threads
