Search results for query: *

This relay is supposed to let the a/c compressor run for 2-10 minutes when heat or defrost are selected and ambient temperature is 25 degrees or more. My compressor is not being shut down and I stopped after 25 minutes. I'm thinking about just disconnecting the 12v lead and doing without it. NOS...

I have just completed putting together a brand new a/c system on a '70 charger, 383 engine. every component is identical to the original parts except for the compressor which is a Sanden 5DSH. The compressor came with 4.5 ounces and the instructions stated "that it was sufficient for the whole...

All major components were new while using original suction and discharge fittings, and the original liquid line. All other fittings and hoses were bought from COLD HOSE. I was able to cut and crimp the fittings and I'm very pleased with the final results. Bought a hydraulic assist crimper from...

Finally have all the components on hand to begin assembling a replacement system for the original a/c system. Everything is brand new. The new compressor is Sanden model SD5S14. The instructions state that the " New Sanden compressors are shipped with all the oil required for a normal OEM system...

I'm in the process of fitting the txv to the original suction tube which attaches to the evaporator. As you can see in the picture the lower copper rod, temperature monitor, will be cut to length and inserted into the small tube. The pressure monitor tube will be screwed onto the threaded...

I'm in the process of replacing everything in the engine bay to complete the system. Everything in the OE ac/heater box has been attended to a few years ago. I intend to use the original suction and discharge metal fittings. The suction side to the evaporator fitting tube is 3/4"od. That...

I have replied to several here on site about the Voodoo 703 camshaft. The part# they offer now is 10240703LUN and is for the Hemi engine. The part# I was responding to was 10230703LUN and was intended for 383/440 engines. The 4th digit is different. In the past they offered the 10230700 series...

The fsm for '70 charger on page2-4, step 3 states to measure from lowest point of one adjusting BLADE to the floor (measurement A). The picture shows a cut-away view of the LCA. I'm not understanding what that is. Secondly, the manual does not mention loosening the bolts to the LCA or jacking up...

Ordered 2 sets of Moog offset bushings K7103 (2 bushings per set) and only received 1 bushing per set. Navigating their website to report the problem was not easy, took almost an hour to figure out the process. Now the good news: 1) They responded via email very quickly to say that the problem...

In the middle of replacing the front-end suspension on a '70 charger. Choose Pro-Forged to order the upper ball joints. When they arrived, I took them out to inspect and test fit them. I had read good reviews about these ball joints, on site here, and also bad reviews about Moog replacements...

rebuilding front suspension on my '70 charger and I'm a 1st timer doing this. Have read countless threads on this, however, can't find a definitive answer on this question. As you see I have pressed out the inner sleeve and the rubber bushing from the lower control arm. The outer sleeve is still...

under normal circumstances, do strut rods need to be replaced when bigger torsion bars are replaced. Do the strut rods wear out like TBs?

I've read thru many of the brake threads and cannot find a definitive answer to this question. I'm in the process of replacing the 3 rubber hoses and fluid. I opened the rear bleed screws to drain those hard lines and then the rear rubber hose. My question is: Shouldn't the forward section of...

Learned a new word yesterday. Learned it here reading thru the drum brake threads. The word is "swage", and for about an hour yesterday I was being "swaged" and didn't even know it. If you don't know the meaning of the word, my definition is: Being tricked into thinking that the right front drum...

Can anyone recommend a neutral safety switch that doesn't leak past the white plastic body and comes with a black rubberized metal seal? I've gone thru several in the past 3+ years and it's always the same leak. I'm considering an Echlin because it states that it's made in the US to the same...

I have read many, many posts on here about wheel and tire sizes, however, most are not about my particular car. I've gone over the 18 inch, gen 2 charger posts endlessly. Before I pull the trigger on this purchase, I'm asking for the final time if those of you who have put 18" wheels on a gen 2...

I'm doing normal a/t Maintenance and adjustments. Did band adjustments and I'm checking the adjustments on the valve body. I've looked at the fsm for the line pressure spring location and it's set properly and I've looked at the adjustment for the kickdown valve adjustment. I don't have the...

When setting up an electric choke, what ambient temp. would you expect the choke valve to be completely closed and what engine temp. would you like to see the fast idle cam come off the adjustment screw? Thanks

Has anyone used this nss and if so, what has been your experience. My current one is fairly new and leaking past the plasic part that's inserted in the metal body. It's no doubt the problem as I can wipe it clean and very shortly see more oil seeping thru. This is when the car is sitting and not...

I'm installing these front seatbelts on a '70 charger. The interior has long been completed but the original shoulder belts were never mounted. I knew someday I would put in a 3 point system. Today's the day and I would like to confirm where the upper harness gets bolted into. I have attached...