Search results for query: *

Followup to earlier post about A/C wiring on 69 Charger. Installed the correct 3 wire A/C switch, had the OE system evacuated and charged with R12. Working great, however, AC guy was worried the compressor wasn't cycling, could lead to evaporator freezing. AC guys, doesn't the RV2 clutch...

Working on daughters 69RT with factory air, getting it ready to be charged/serviced. Started wiring up the A/C controls and noticed there were 2 fan switches in the parts box, one with 3 wire harness and one with 4 incl a separate connector. OK, so check out the FSM schematics and the...

Running Goodyear Polyglas G70-15 reproductions on my 70rr. Tires are now about 12yrs old, though look brand new as they probably have about 3000mi. Sidewalls are good and they hold air very well. Always garaged. Opinion on whether I should replace them based on age?

OE starter in my 70RR was doing the single <solenoid> click dance a few weeks ago, so I pulled it to disassemble and inspect. Since I had it apart, replaced solenoid, cleaned/checked armature, brushes were good, clutch good, new battery stud and contact assembly (old ones had some divots)...

440-6, 8yr old build, stealth heads, stock manifolds, Lunati 60303 cam/hyd lifter kit, 10.2CR. Brad Penn 15W-40 with Wix 51515. Starts and runs good, except for moderate rattle noise at cold startup. Rattle goes away after 5-7sec. Oil pressure approx 35 at idle, 60 at cruise. Before I yank...

Purchased passenger side qtr and door glass for the RR about 6 months ago. Inspection of the pieces prior to install showed no defects, etching, or otherwise. Install was big job, but very careful with the glass. RR has been in the garage since, with a cover. Today I was working on the RR...

As shown in pic, leaks between metal housing at end of cable and cable. Everything else seems dry. Is this an inner seal issue?

Need to replace quarter glass. 70RR conv though believe it's similar to hardtop. Got the front guide out OK, removed rollers. FSM says to remove regulator arm stud retainers and studs from frame. Can barely see the retainers, let alone remove them. Anyone done this...advice?

70RR vert, power windows. Vent frames are correct, from 67B hardtop. Glass is original. Door alignment is good. Passenger door glass is misaligned. When fully raised, it is outboard of roof rail weatherstrip and misaligned with qtr glass at top. If adjusted to bring alignment closer...

Daughter's fiance, retired USMC gunny, just bought this 57 Dodge in Arizona. Has a 318/727 transplant, runs, but needs lotsa attention. The 318 has shorty headers, HEI distributor, 4 barrel Holley and sounds like it might have a stepped up cam. We happened to pick it up on the hottest day of...

Looking for a core that works. Anything between 68 and 72 should be ok. Appearance not impt.

Anyone know what years/models will interchange with 69B strut rod? Need one for daughters 69 Charger.

For 69 Charger, good used is fine

Need the 2 A/C center vents for 69 Charger

Looking for working heater valve (firewall) for 69B A/C car. Also dash center A/C registers.

Core is fine as long as it's rebuildable. Single field, double pulley. Ideally with date code for 19Dec68 build. Edit: single pulley OK

1970 Plymouth Sport Satellite, yellow with white vinyl roof, white/black interior, 318 V8, 904 auto, bucket seats/console, A/C, PS. Was daughters driver for several years, currently not running. Resto begun, but unable to continue. 99% all there including nice console, dash/gauges, nice...

.030 over, stealth heads, SRP pistons approx .006 in the hole, stock iron manifolds, Lunati 60303, stock rockers, 10:2CR, TTI 2.5 exhaust, pertronix II with flamethrower II coil. Carbs are new 71 repros, 65jets, 6.5PV, #35 squirter. Engine is on test stand with 727 attached. Engine idles at...

Just removed old top from my 70RR conv. Working on frame now. Has anyone installed their own conv top? Would appreciate any suggestions/guidance.

70RR convertible: 68 440 block (.030 over) with repro 6pak carbs, 440source alum heads, stock iron intake and exhaust manifolds, stock rockers, SRP flat tops (approx 10:1), SCAT H beam rods, 727, 3.23 suregrip. Mostly street car with a little attitude. Looking at following cam options: comp...