Search results for query: *

I have a pair of rear dodge taillight trim surrounds. From my 1968 dodge coronet. They are in very good condition. Price is $130 plus 10.50 usps post from San Jose CA Thanks for lookin.

I have a pair of 68 dodge seat belt clips. These mount with the visor screws on both sides. Maybe it's the last thing you need! $60.00 obo plus $10.50post from San Jose CA Thanks for looking.

I have 3 of 4 door panels for 1968 dodge coronet 500. They could be used as templates or possibly be restored. They are burgundy. Thanks for lookin. 100 obo plus post or ok to pick up in san jose ca.

Hello again. Mine is a 1968 b body with a 440 and 727. Will the A518 fit behind my 440? The 518 is an overdrive right? Or please help me with other auto trans ideas. I would like to put the 391 gears back in.

In my 68 B Body 440 engine - I am ready to rebuild the transmission. In my past I have always done manual transmissions. Please help understand 2 things about the TF 727. 1. Using the valve body that does not require the kick down rod. What it's called and how to do? 2. Please give me the...

In my 68 B Body 440 engine - I am ready to rebuild the transmission. In my past I have always done manual transmissions. Please help understand 2 things about the TF 727. 1. Using the valve body that does not require the kick down rod. What it's called and how to do? 2. Please give me the...

Mine is a 68 Coronet 500 - Superbee with a 440. I have attached pics of the mufflers. I am hoping to make it quieter by adding 24 inch glasspacks. Seeking your opinions on this move. I really like the tips so I'd rather not change those. What will I gain with the added glasspacks? Thanks in...

Mine is a 1968 Coronet 500 440 TF727. It came with air shocks when I bought it but had no air lines. I installed new lines but I do not like the ride. Do you think it's best to go back to normal shocks? I am thinking yes. Thanks for your input.

Hi to all! Mine is a 1968 Coronet 500 Super Bee. As some of you know I have been solving a vibration problem and tonight I planned on installing the new flex plate made to solve a mismatch between the cast crank 440 and the non weighted torque converter. I learned that the transmission will...

Hi - It's Scott in San Jose. I think many you will know the answer to my question. Mine is a 1968 Dodge B body. I noticed the inner seal in the rear end housing then the gasket at the 5 bolt flange. How are the outer axle bearings serviced? Hand pack them like front spindle bearings? Thank you!

Mine is a 68 Coronet 500 that came with a 383. Now it has a 440. What changes do I need to make to the 727 so it will work behind the 440? Thanks as always! Scott

Here is my 1968 Dodge Coronet 500 for sale. It is a Super Bee tribute done tastefully. I'm only selling it to make room for the next project. Located in San Jose CA. The engine is 440 with 825 Edelbrock carb, headers, high energy ignition. The transmission is a Torqueflight 727 column...

If my speedo reads too high do I get a gear with more teeth or less. Currently mine has 26 teeth. 68 Dodge Coronet 500 727 trans.

Mine is a 68 Coronet/Superbee with a 440 and torqueflight 727. Under acceleration there is a vibration or flutter that starts at 20 mph or so. When I put it in neutral it goes away. I pulled the driveshaft and checked the U joints. They were ok. I have considered a trans rebuild but am...

I am about to install a front sway bar on my 68 Coronet. It never had one before. Can anyone send a diagram of the brackets, measurements, etc. I will need to install it? Thanks of course!

68 b body coupe. I count 14 seat belt components (excluding the front hangers and the bolts in the count) Back seat has 6 pieces - 3 male and 3 female front seat has 8 pieces - right and left retractable male, 2 hanging female for shoulder that clip into the roof mount, right and left lap...

Rather than pay $500 for their tach I bought one from an amazon seller and installed it on the right of the sweep style dash. Turned out ok.

Mine is a 68 Coronet 500. Currently it has a PS setup but when I got the car there was no pump etc. Now that I have installed the pump and pully the PS box is a leaker. Better to just put in a new ps box or is a manual box ok? Thanks as always

1968 Dodge Coronet. Mine has a sweep style speedo. The dash lights do not work. If it is a faulty ground please let me know where to attach the ground. The oil pressure light works. Gas gauge and temp gauge do not work. The ammeter has a fault so it is bypassed. Thanks for your help...

I started this in July. There are some fun reasons explaining why I tributed this coronet. Here see before and now. I'll post the middle photos later. Thanks for not hating.