Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
I just seen pics of a 440 stamping was was shaved off. On the front engine boss, only part of the info was there. The F440 was there & the letters HP were there. Looks like any other info were machined off. Any reason for that to be done ??
My La built 70 RR six barrells fender tag does not list the 3 spd wipers on it. I know they were std on this car. Should the fender tag have them listed ??
I have a 70 Roadrunner V code that I would rather trade or would sale & get another car. My car has the numbers matching 440. Correct 1970 727 not numbers matching. Motor has been completely rebuilt less than 900 miles since rebuild. I put on 440 source aluminum heads. A lot of the engine parts...
I know this needs to go in the parts wanted section, but here goes. Someone used to make a hand made tool to adjust the rear carb a/f screws. Does anyone have one for sale or know where I can get one.
I'm having trouble adjusting the a/f ratio screws on the center carb. There is no difference when either side is adjusted. I can screw them all the way in & no change. So, what needs to be checked or fixed ?? I'm also getting 15 on the vacuum guage. And strong gas smell after shut down.
1970 RR 440. I'm thinking about putting a ground wire on my engine. Does someone have made up already or do we just make one. If we make one, what gauge wire & where to connect it.
1970 Ralley dash on a RR. Been having issues with either no oil pressure showing on the gauge or it pegs past 80 lbs. I am on the third sending unit and no change. Decided to change the gauge itself. Still nothing. I also have the RTE voltage limiter. And the wiring is 10 yr old M&H. I need some...
1970 440 six barrell. I needed to take the center carb off last nite. Of course one of the fuel inlets was turning when I was removing the fuel line. It's tough to get a wrench solidly on the inlet. Does Holley or someone make a tool for that occasion.
My oil pressure guage ( 70 Ralley dash ) has been going wonky lately. While driving it sometimes goes to zero pressure & then reads appx 20-30 lbs of pressure. We've tested the engine with a mechanical guage & it reads appx 75-80. We replaced the sending unit. It showed appx 60 lbs. Now today...
A couple days ago while driving my car, I stopped at a red light. The oil guage went to "0" ( zero ). I made a quick right turn to get off the road & the oil pressure shot up to 20 lbs. 20lbs is still not good but good enough to get home. After some deliberation, we put a mechanical guage on the...
I need some pics of the carb linkage & spring set up of a six barrell set up. Must be an automatic trans set up. Thank You !!
Also does anyone know where to get that little clip.
Not sure if i'm in the correct forum. Here goes. I was trying to adjust the time on the clock. While pulling the adjuster out. It came completely out of the housing. Is it fixable ?? If so, what do I have to do ??
1970 RR w/ 440 + 6. Chrysler electronic ignition. Orange electronic voltage regulator & newer ballast resistor. Cruising down the road today, the engine just stops running. Put it in neutral & drifted into a parking lot. The engine started right back up. What do I need to check or replace.
I have my spare set of 1970 HP exhaust manifolds for sale. I don't know what else they fit, but they came of my 70 RR. These are 2 perfect manifolds. The heat riser has had the repair kit put on it. They were just media blasted & are ready to go. They are date coded October 1969. $ 500 + appx $...
I got a 1970 440 + 6. Just finished new 440 Source aluminum heads. Car starts just fine. But when i give it some gas under load the engine sputters & wants to die. Choke seems to be working fine, I just checked & adjusted the floats. What else should I check to correct the problem. Could it be a...
I'm looking for a pix of the spring & throttle setup for a six barrell. I had mine off & am not sure i have it back on correctly. Any help is appreciated.