What did you do to your Mopar today?

[Propwash]

Finished aligning doors and installed all new rear drums/hardware/springs

 

[Red63440]

I installed my pumpkin with my new sure grip unit unit and 3;23.1 gears, installed my drive shaft, axels and drums and filled it with fluid. Started the car and let it run for 10 or 15 min. on the stands to check for leaks or noises.
Tomorrow I will mount the rear tires, take it off the stands and get the engine ready to pull. The car is going in for paint......:headbang:

 

[cam383]

Set the valves for the next race weekend.

 

[Ron 73]

Looking out the window at clouds full of rain about to give it a bath.. wishing... as i wait for Hughes net company who i should have known would be late. Making calls for a new kick-down cable with throttle cable all in one unit...I hope.. And via email getting some interior screws im missing. Still repairing wires, And put For BBody sticker on windshield..

Actually sticker was yesterday.

'

 

[wedge5]

Put the Decals on the doors and started the cross ram install.

 

[Ron 73]

WOW! If i say more ill have to clean keyboard. WOW

 

[Joe Mopar]

Chasing gremlins.

 

[67 B-body]

Lookin GREAT Wedge!

 

[Finallygotmine]

Back on the stands today. Going to attempt to put in my Mass flo EFI system. Took off the intake, carb, coil. Aiming at dropping the tank tomorrow. Pray for me. LOL

 

[Propwash]

Good luck to ya Daryn...Post up some pic's of the surgery on your bird

 

[MustangAndy]

Ran down some wiring gremlins ------ and broke my e-brake cable
It went click, click, snap,floor. have to put that on the parts list now too.


and took this:

 

[shag766]

installed tremec with bell housing to take measurement for new dr/shaft.

 

[shag766]

tti

installed the 40 micron f/filter close to the f/tank and test fitted the 80 micron after the pump. snugged up the 1/2" f/line and emergency brake lines to the rear disc brakes. set the hemi in place for fit and clearance check. it's real close to the r/front shock tower housing. hope the tti's are as good as they claim. when i ordered them for a 69 b-body using shumacher kit they said ok. looks real close. tomorrow is another day.

the pass side went on slick. lift the elephant about 1" on in they went. drive side will be interesting with steering box. oh well, if it was easy anybody could do it.

 

[mark42202]

Ordered my racing seats and Ultra Bell for the Coronet... then took the Moroso electric water pump drive motor off and installed March aluminum pullies, fan, and fan belt on the Fury. Also cleaned up a bunch of wires under the dash around the 6AL, removed the 3 step module, and removed the wiring for said electric w/p motor.

 

[watermelon]

gave it a shower of Meguiars Quick Detailer.

 

[Finallygotmine]

Dropped the gas tank without blowing myself up and planned the routing of the new fuel pump, filter and regulator. Oh, and ordered a new throttle cable.

 

[Propwash]

Dialed in the torsion bars, Installed the parking brake cables, finished off body work on rear of car, dropped car to the ground...Finally! Sprayed inside of new fenders with SEM Bedliner, jigged up Sub frame connectors

 

[MustangAndy]

Think I need a new one?


Tank itself is swiss cheese to top it all off.

 

[Propwash]

Sprayed the hinges with some OMNI single stage as well as the area they mount up to on the hood...

 

[Joe Mopar]

Replaced voltage regulator. Went out to a small cruise night at a local B&G.