Search results for query: *

Looking for the stainless trim that goes around the outside of the back glass for a 66 satellite hard top. I think 66/67 belvedere 2 and coronet are the same. 2 door hard top only, pretty sure the 4 door trim wont fit. Looking for driver quality, not a show car. Thanks

I can't remember where these came from, probably dash or console as that was the last thing I was working on...any help. It's a 66 satellite, thanks!

Having a heck of a time getting the upper trim to line up with the a-pillar trim on both sides. Do these clips look correct? Any tips? Thanks.

My 1966 Satellite came with this console top on it, but in every picture I've seen of the consoles they dont have this aluminum plate over the ridges. I am wondering if this is correct or off of something else, like a charger maybe, or another year? Also would the console door have had a plate...

I am trying to reassemble the front end of my 66 satellite and finding lots of bolt holes are not lined up. I'm now suspicious that it may have had a front end collision and was not properly fixed before being painted. Can someone here help with some pictures of the upper and lower grille...

Looking for some advice on tuning my new rebuild. Let me start by saying that this is my first engine build so I don't have a lot of experience to lean on. I've been reading and watching plenty of video's on carb and timing set up, but still a bit unclear on which to adjust and in what order...

I'm in the middle of fixing the partially burned wire harness in my 1966 satellite. This connector is causing me some confusion. The violet w/tracer coming from the console harness has a second short wire and terminal, anybody know where this connects. I have the fsm but don't see the console...

As the title said, for the purpose of breaking in a new engine without spinning the pump in the trans, will a 130 tooth 10.5 inch flywheel fit/work for this?

1966 Satellite, new aftermarket spectra tank and sending unit. How far should the pick up be from the bottom of the tank? It seems a bit high off of the floor of the tank, maybe 3/4 inch or so at the closest. Also should the float contact the floor when totally empty, because this one sits...

I'm getting the fuel system cleaned up on my satellite before dropping the new engine in, and thinking about plumbing a return/vapor line to prevent vapor lock. My current thought is to weld a 1/8 ntp bung into the upper front portion of the tank and plum the line in there. Has anyone here...

I'm finishing up my 440 build and am trying to get all the front accessories figured out before the engine goes in, and I'm running into a bit of a headache with the power steering. I know I could just go drop $300-$400 at 440 source and get everything I need to swap to a Saginaw set up, but...

I need a new boot for my '66 Satellite, it's oval and has 6 screws, all the boots I can find are round with 3 screws and are listed as '66-'74 A and B. Even Year One has the round boot listed for '66. Is the round boot correct? If so does anyone know what the oval boot would be off of? I...

Does anyone know of a source for this connector? I'm going through my dash harness and fixing some issues, I'd like to replace with the same connector rather than individual connectors if possible. I believe it is for the wiper motor switch.

Can anyone help identify these parts? Years later I'm still sorting through boxes of parts from a rolling shell that I bought thinking it would be a quick and easy project. :lol: They are possibly off of a 66 satellite or 68 new yorker engine.

Bought a 66 satellite rolling shell years ago and been slowly putting it back together, tried to mock up a new radiator today and I think my core support is out of whack. Having trouble finding good pictures to confirm, but I'm guessing it's supposed to be flat, and the lower support should be...

Tried to mock up my new ecp 22" radiator today and found that the mounting holes on my core support (66 satellite) are different from the radiator. My satellite has 4 holes 24.5 in apart horizontal and 14.5" vertical. The radiator is correct in the horizontal, but the passenger side flange is...

Rebuilding a donor trans for my satellite and wondering what is this part attached in-between the trans and the speedo cable? Trans is a 71 bb 727.

I need to find all of the Console linkage between the shifter and trans for my 1966 Satellite. I've found several listings for 67-70, and one eBay listing for 66 only, and still other listings for 66-70... yet in pictures it all looks the same. Is the linkage for 1966 unique? If not will all...

I got my block back from the machine shop this week and after getting it on the stand and looking it over I noticed a couple of the cam bearing oil holes aren't fully lined up with the oil holes. Specifically the #4 and #5 (worst) are a bit off, this is my first time rebuilding an engine, I'm...

I've come here for some help and guidance. I have a '66 Satellite that I have been slowly working on for about the last 10 years, I bought it as a rolling shell and the seller included a '68 440 and a '71 727. The engine looks like it was marked from a junk yard as it has "1968 New Yorker"...